كود:
smartctl version 5.33 [i686-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD800JB-00FMA0
Serial Number: WD-WMAJ94487192
Firmware Version: 13.03G13
User Capacity: 80,026,361,856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jan 21 01:24:13 2007 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command
from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (2460) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off supp
ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 35) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_
FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 179 174 051 Pre-fail Always -
65821
3 Spin_Up_Time 0x0007 100 100 021 Pre-fail Always -
2333
4 Start_Stop_Count 0x0032 100 100 040 Old_age Always -
79
5 Reallocated_Sector_Ct 0x0033 117 117 140 Pre-fail Always FAILI
NG_NOW 661
7 Seek_Error_Rate 0x000b 200 102 051 Pre-fail Always -
0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always -
17262
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always -
0
11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always -
79
194 Temperature_Celsius 0x0022 106 014 000 Old_age Always -
37
196 Reallocated_Event_Count 0x0032 090 090 000 Old_age Always -
110
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always -
0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always -
0
200 Multi_Zone_Error_Rate 0x0009 200 198 051 Pre-fail Offline -
0
SMART Error Log Version: 1
Warning: ATA error count 23 inconsistent with error log pointer 5
ATA Error Count: 23 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 23 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 2e c7 fb 3c e0 Error: UNC 46 sectors at LBA = 0x003cfbc7 = 3996615
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 28 cd fb 3c 00 50 00:01:06.405 READ DMA
c8 00 30 c5 fb 3c 00 50 00:01:04.485 READ DMA
c8 00 38 bd fb 3c 00 50 00:01:02.570 READ DMA
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
Error 22 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 30 c5 fb 3c 00 50 00:01:04.485 READ DMA
c8 00 38 bd fb 3c 00 50 00:01:02.570 READ DMA
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
Error 21 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 38 bd fb 3c 00 50 00:01:02.570 READ DMA
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
c8 00 58 9d fb 3c 00 50 00:00:54.920 READ DMA
Error 20 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
c8 00 58 9d fb 3c 00 50 00:00:54.920 READ DMA
c8 00 60 95 fb 3c 00 50 00:00:53.010 READ DMA
Error 19 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
c8 00 58 9d fb 3c 00 50 00:00:54.920 READ DMA
c8 00 60 95 fb 3c 00 50 00:00:53.010 READ DMA
c8 00 68 8d fb 3c 00 50 00:00:51.125 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
هذي النتيحه من تنفيذ الأمر
بس ياجماعه وش معنى الرساله
وصعبه اني آخذ باك كل فترة لأن حجمهم كبير والمنتديات تتحدث ولاعندي سيرفر ثاني انقلهم عليه غير جهازي
رد مع اقتباس
