كود:
smartctl version 5.33 [i686-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD800JB-00FMA0
Serial Number: WD-WMAJ94487192
Firmware Version: 13.03G13
User Capacity: 80,026,361,856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jan 21 01:24:13 2007 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command
from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (2460) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off supp
ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 35) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_
FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 179 174 051 Pre-fail Always -
65821
3 Spin_Up_Time 0x0007 100 100 021 Pre-fail Always -
2333
4 Start_Stop_Count 0x0032 100 100 040 Old_age Always -
79
5 Reallocated_Sector_Ct 0x0033 117 117 140 Pre-fail Always FAILI
NG_NOW 661
7 Seek_Error_Rate 0x000b 200 102 051 Pre-fail Always -
0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always -
17262
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always -
0
11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always -
79
194 Temperature_Celsius 0x0022 106 014 000 Old_age Always -
37
196 Reallocated_Event_Count 0x0032 090 090 000 Old_age Always -
110
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always -
0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always -
0
200 Multi_Zone_Error_Rate 0x0009 200 198 051 Pre-fail Offline -
0
SMART Error Log Version: 1
Warning: ATA error count 23 inconsistent with error log pointer 5
ATA Error Count: 23 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 23 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 2e c7 fb 3c e0 Error: UNC 46 sectors at LBA = 0x003cfbc7 = 3996615
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 28 cd fb 3c 00 50 00:01:06.405 READ DMA
c8 00 30 c5 fb 3c 00 50 00:01:04.485 READ DMA
c8 00 38 bd fb 3c 00 50 00:01:02.570 READ DMA
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
Error 22 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 30 c5 fb 3c 00 50 00:01:04.485 READ DMA
c8 00 38 bd fb 3c 00 50 00:01:02.570 READ DMA
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
Error 21 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 38 bd fb 3c 00 50 00:01:02.570 READ DMA
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
c8 00 58 9d fb 3c 00 50 00:00:54.920 READ DMA
Error 20 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 b5 fb 3c 00 50 00:01:00.660 READ DMA
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
c8 00 58 9d fb 3c 00 50 00:00:54.920 READ DMA
c8 00 60 95 fb 3c 00 50 00:00:53.010 READ DMA
Error 19 occurred at disk power-on lifetime: 15100 hours (629 days + 4 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 35 c0 fb 3c e0 Error: UNC 53 sectors at LBA = 0x003cfbc0 = 3996608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 48 ad fb 3c 00 50 00:00:58.745 READ DMA
c8 00 50 a5 fb 3c 00 50 00:00:56.830 READ DMA
c8 00 58 9d fb 3c 00 50 00:00:54.920 READ DMA
c8 00 60 95 fb 3c 00 50 00:00:53.010 READ DMA
c8 00 68 8d fb 3c 00 50 00:00:51.125 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
هذي النتيحه من تنفيذ الأمر
بس ياجماعه وش معنى الرساله
وصعبه اني آخذ باك كل فترة لأن حجمهم كبير والمنتديات تتحدث ولاعندي سيرفر ثاني انقلهم عليه غير جهازي